Cookie preferences
This website uses cookies, which are necessary for the technical operation of the website and are always set. Other cookies, which increase the comfort when using this website, are used for direct advertising or to facilitate interaction with other websites and social networks, are only set with your consent.
Cycle Display with lots of displayed values
With the CA the controller can be programmed and has a connection for the temperature sensor of the motor
Dimensions: 128 x 57 x 26 mm
140cm cable terminated with 6-pin JST-SM series connector.
Includes:
- Analogger Cable
- THUN Sensor Cable
- Accessories Cabling
- DC Power Cable
- Handlebar Mounting Bracket
Direct Plug-in models need to be to have their RShunt value calibrated to match the shunt resistance inside the controller, rather than left at the default 1.00mOhm. All of our controllers have the calibrated RShunt printed on the label, and most other vendors provide this information as well.
Once connected to the vehicle's power bus, the Cycle Analyst calculates and shows the following information:
- Volts, Watts, Amps: The instantaneous electric power being drawn from the battery.
- Amp-Hours, Watt Hours: The net energy that has been pulled from the pack since the meter was reset. The accumulated amp-hours let you know the remaining energy in the battery pack with far greater accuracy than a voltage or LED indicator.
- Speed, Distance, Time: All of the basic features of a bicycle computer, including the average and maximum trip speeds, plus a total distance odometer.
- Regen, Wh/km: There are several quantities this meter will calculate that you don't get with other instrumentation, such as the % extra range that was gained from regenerative braking, as well as the vehicle's average energy use in Watt-hours per kilometer or mile.
- Peak Currents and Voltage Sag: Records the maximum forwards and regenerative currents as well as the minimum voltage on the battery pack.
- Total Battery Cycles and Amp-Hours: Retains life cycle information on the vehicle's battery pack, such as how many charge and discharge cycles the pack has experienced and the total amp-hours that were delivered over its entire life.
Furthermore, the Cycle Analyst has the ability to over-ride the user's throttle and regulate the power delivered to the motor, turning an otherwise dumb ebike into an intelligent device with a user programmable speed limit, current limit, and low voltage cutout.
- Speed Limit: This has the utility of providing legal compliance to the speed cap imposed on ebikes in most jurisdictions. When used with a full throttle, it serves as a cruise control on the electric bicycle. It can also be beneficial to riders who want to increase their torque and power by using a higher voltage battery, without simultaneously increasing their top-end speed.
- Current Limit: An adjustable amps limit is useful to prevent damage to the batteries from excessive current draw, to increase the range that you'll get on a charge, and to protect the motor controller and motor in setups that draws too many amps.
- Voltage Cutout: A low voltage cutout is used to protect a battery pack from being discharged too deeply, which can cause cell reversals in NiMH/NiCad packs, permanent cell damage in Lithium packs, and sulfation in Lead Acid batteries. The programmable low voltage rollback allows you to set an appropriate low voltage point tailored to your pack.
For more information please see the Cycle Analyst homepage
It isn't possible to use a hall signal from the motor to get the speed, because the magnet speed sensor only is connected to the CA PCB, not the Direct-Plug-Connector.
Available downloads:
Customer evaluation for "Cycle Analyst V3 DPS direct plug in with Speedometer"
From: Leon H.
Gute Qualität
Grin steht für gute Qualität, das sieht man bei diesem Analyst. Die Ansicht könnte zwar etwas moderner sein, aber dafür hat man fast unbegrenzte Anzeige- und Änderungsmöglichkeiten.
Write an evaluation
Evaluations will be activated after verification.
Programmierkabel für
Phaserunner
Cycle Analyst
Cycle Satiator
rechts
ohne Stecker
TIP!
Bremssensor
EMPFOHLEN
Anti-Blitz
bis 120A
TIP!
EMPFOHLEN
Schaltsensor
für Ketten- und
Nabenschaltung
schont Kette
TIP!
EMPFOHLEN
Montagetool
für 2. Sicherungsring
Drehmoment
Ausbau Hollowtech 2
TIP!
passt zu Akku-
Stecker BBSHD
TIP!
TIP!
TIP!
TIP!
TIP!
rechts
EMPFOHLEN
Montagetool
für 1. Sicherungsring
Drehmoment
TOPSELLER
links
rechts
TIP!
EMPFOHLEN
110 Nm
Drehmoment
36-52V
TIP!
EMPFOHLEN
komplettes Set
36-52V
110 Nm
TIP!
TIP!
TIP!
TIP!
EMPFOHLEN
Montagetool
für 1. Sicherungsring
Drehmoment
EMPFOHLEN
Montagetool
für 2. Sicherungsring
Drehmoment
Ausbau Hollowtech 2
TIP!
Demontagetool
für Vierkantkurbeln
Demontagetool
Innenlager
Octalink
TIP!
EMPFOHLEN
zusätzliche
Akkubefestigung
Verlängerungskabel
Display
50 cm