Cookie preferences
This website uses cookies, which are necessary for the technical operation of the website and are always set. Other cookies, which increase the comfort when using this website, are used for direct advertising or to facilitate interaction with other websites and social networks, are only set with your consent.
Products from GRIN
No results were found for the filter!
TIP!
Cooling for Hub Motors The original Statorade by ebikes.ca is used. You have to seal the motor afterwards. Togheter with a syringe The ferrofluid provides a better transfer of heat to the engine housing and the heat can be transported...
€34.99 * €39.99 *
Ready to ship today,
Delivery time appr. 1-8 workdays
Cycle Display with lots of displayed values With the CA the controller can be programmed and has a connection for the temperature sensor of the motor Dimensions: 128 x 57 x 26 mm 140cm cable terminated with 6-pin JST-SM series connector....
€189.99 *
Ready to ship today,
Delivery time appr. 1-8 workdays
3 Button Control for Cycle Analyst V3 Narrow profile 3 button, up/down digital Aux input for V3.1 Cycle Analyst firmware. Lets you change any limit or pedal assist setting up or down in a customizable number of steps. The wiring allows...
€24.99 * €34.99 *
Ready to ship today,
Delivery time appr. 1-8 workdays
For a quick mode change on Cycle Anaylst This 3 way switch is used as an auxiliary input device for the V3 Cycle Analyst. It has resistors inside to produce 3 different voltages (1.6, 2.5, and 3.3V) for each switch position and can be...
€12.99 * €19.99 *
Ready to ship today,
Delivery time appr. 1-8 workdays
Programmierkabel für
Phaserunner
Cycle Analyst
Cycle Satiator
This cable is used to program, update and log the Cycle Analyst , Phaserunner and Satiator with a Computer. Cable length: 300 cm It is equippent with a genuine FTDI FT232R chipset, probably you need to install the driver Works for Cycle...
€19.99 * €31.99 *
Ready to ship today,
Delivery time appr. 1-8 workdays
Steel mounting bracket for Cycle Analyst Ahead Steerer Tube Mount for Cycle Analyst (it is not Grin Manufactured). 1/4" Bolt Hole for Cycle Analyst. fits over 1 1/8" steerer tube 2 mm stainless steel the adapter can be bendet as you like...
€12.99 * €15.99 *
Ready to ship today,
Delivery time appr. 1-8 workdays
Resistor for your ebike project 0.5 mOhm external shunt for Cycle Analyst. Manufacturer Grin says they can handle up to 150A continuous, 400A peak. It says 100A on the shunt. Dimensions: 134 x 29 x 28 mm
€24.99 * €39.99 *
Ready to ship today,
Delivery time appr. 1-8 workdays
0.25 mOhm external shunt for Cycle Analyst Grin says they can handle up to 300A continuous, 800A peak. It says 200A on the shunt. Dimensions: 134 x 29 x 28 mm
€24.99 * €39.99 *
Ready to ship today,
Delivery time appr. 1-8 workdays
Precision 1mOhm Stand Alone Shunt With Pigtail Leads and 6-Pin CA-DP Plug. Includes Throttle Pass-Thru. Molded 1mOhm stand alone Cycle Analyst shunt with pass thru of throttle and speedo wires for 3rd party controller integration.
€19.99 * €39.99 *
Ready to ship today,
Delivery time appr. 1-8 workdays
PAS sensor for use with Cycle Analyst V3 Plug & Play Cycle Analyst V3, compatible with 10V Standard, 12 Pole Magnet Ring and Pedelec Sensor. Works left and right and without unmounting the crank. Connector PINs contacts: 5, Cable length:...
€29.99 * €34.99 *
Ready to ship today,
Delivery time appr. 1-8 workdays
EMPFOHLEN
zusätzliche
Akkubefestigung
With this Bottle Bobs you can secure your Downtube and Water Bottle Batterie to frames without eyelets Helps when installing downtube and waterbottle batteries on bike frames that don't have properly located waterbottle braze-ons. Or...
€34.99 *
Ready to ship today,
Delivery time appr. 1-8 workdays
TIP!
Cable collection for your E-Bike Suitable for collecting and hiding cables, as well as protecting them from dirt. We mostly use it to hide the remaining cable lengths of display, throttle, etc. It´s already part of the Cycle Analyst V3.
€8.99 *
Ready to ship today,
Delivery time appr. 1-8 workdays