>>> CONFIGURE NOW <<<
 

Spare Parts for your Bafang BBS01 or Bafang BBS02 System

Here you will find the necessary spare parts to repair your Bafang BBS01 or Bafang BBS02 motor. Also spare components of this system are included, for example speed sensor, crank bolts or cranks. You can see the compatibility with your system by checking the product name. Here you can find a picture with the named motor parts, incl. linked products.

2 From 3
No results were found for the filter!
Bafang BBS02 Stator with housing
Original Bafang Stator for BBS02 Motor You need to change the core if you have hall sensor error or shorted. In case of overheating, we recommend to change stator and rotor , as the rotor is demagnetized under high heat conditions - and...
€144.99 *

Ready to ship today,
Delivery time appr. 1-8 workdays

Bafang BBS02 Rotor with Bearing
Original product for Bafang BBS02, suitable for 48V and 52V batteries. Doesn't work with BBSHD
€94.99 *

Ready to ship today,
Delivery time appr. 1-8 workdays

Bafang BBS01 BBS02 Axle Extension 100 mm Press...
Perfect for wider bottom brackets in combination with BBS01 & BBS02 motors All you need to do is disassemble the BBS01/02 and install the the new components as shown. This kit will convert your Bafang mid drive to fit in a FAT Bike much...
€139.99 *

Delivery time 25 Workdays

Bafang BBS01 BBS02 Pinion Gear
Original product for the Bafang BBS01 and BBS02. For newer Version B and 12 mm shaft diameter or Version A with 10 mm diameter for older models. There are different versions out there. Look in the picture for the right one. We recommend...
€39.99 *

Ready to ship today,
Delivery time appr. 1-8 workdays

Bafang BBS Triangle Bottom Bracket Spare Set
For mounting the Bafang BBS Motors on the Bicycle Included parts: 1 x Mounting Triangle Plate with 2 screws 1x Inner main Lockring adapter (50-60 Nm) 1x Outer Lockring adapter (25-30 Nm) Fits for Bafang BBSHD, BBS01 and BBS02 motors....
€34.99 *

Ready to ship today,
Delivery time appr. 1-8 workdays

Bafang BBS01 BBS02 Rubber Seal for Phase and Hall
Rubber Seals between Controller and Stator Essentially if you change something inside the motor (e.g. nylon gear , motor core ) nad you have to cut out the silicone protection. Usually it breaks and it is hard to get them clean. Original...
€8.99 *

Ready to ship today,
Delivery time appr. 1-8 workdays

Bafang BBS Crankarm Mounting Bolts
Set of original Bafang crank M8 screws for BBSHD, BBS02 and BBS01 Motors. Observe the right hand side when mounting the cranks. They are marked with L and R. Tight the crank with force, blue bolt lock is already on the screws.
€7.49 *

Ready to ship today,
Delivery time appr. 1-8 workdays

Bafang BBS01 BBS02 Nylon Reduction Gear
With integrated bearings, Original product of Bafang BBS01 and BBS02. This one is for Version B . For a noise reduction it is made of nylon. For this reason, it is more vulnerabile if excessive forces act and at the same time no crank...
€39.99 *

Ready to ship today,
Delivery time appr. 1-8 workdays

Bafang BBS PAS Sensor Board 8FUN-MS-1
Sensor Board for PAS registration If only the throttle works, you can try to change the Bafang PAS sensor board for replacement. It can be caused by a faulty pas disc as well as a faulty PAS board. Suitable for BBSHD, BBS02 and BBS01...
€31.99 *

Ready to ship today,
Delivery time appr. 1-8 workdays

Bafang BBS01 BBS02 Plastic Cover Secondary...
Gearbox-Cover for Bafang BBS01/02 Motor Original product for the Bafang BBS01 and BBS02, version with 7 screw holes. This one is for Version B . There are different versions out there. Check the pictures for the right one. There is a...
€20.99 *

Ready to ship today,
Delivery time appr. 1-8 workdays

Bafang BBS Needle Bearing NK17/16
Bearing between Axle and Sleeve You can find it inside the axle sleeve. Dimensions: Inside: 17 mm, Outside: 25 mm, Width: 16 mm Works for BBS01, BBS02 and BBSHD Motors. It is a standard size and can be found in ball bearings stores, ours...
€16.99 *

Ready to ship today,
Delivery time appr. 1-8 workdays

Bafang BBS Axle Bearing 42 mm 16004RS
Bearing between PAS disc and Clutch 16004RS, is a standard size and can be found in bearing stores. This bearing can be found on the Bafang BBSHD, BBS01 and BBS02 (B model) axle between PAS disc and clutch. Please check the right size...
€18.99 *

Ready to ship today,
Delivery time appr. 1-8 workdays

2 From 3

Article not found?

Your needed spare part for Bafang BBS01 or Bafang BBS02 is not included? Please let us know and send an e-mail. Note: Spare Parts for Bafang BBSHD can be found HERE.

Viewed