Register now for our newsletter!

Subscribe to our free newsletter now and don´t miss any more promotions and news.

Bitte geben Sie eine gültige eMail-Adresse ein.
>>> CONFIGURE NOW <<<
 

50A 30-90V Phaserunner Motor Controller V3

€339.99 *

Prices incl. 19% VAT plus shipping costs

Delivery time 100 Workdays

Farbe wählen:

Kabelset inklusive:

The new V3-Version of this popular motor controller is available in 2 different colors: Silver or Black (please choose above)! Also available with L1019 motor cable plug!

Ultra compact field-oriented motor controller, yet still capable of 90V max with 96A peak phase currents (~40A Continuous). New 2020 V3 model with WP8 CA Plug. The required adaptor cable to connect Cycle Analyst can be added per request.

Optional with cable set:

1) Battery only

  • 80 cm High Flex Battery Cable from XT60 to Anderson 45 (2x 13 + 2x 18 AWG)

2) BBSHD:  

  • 80 cm High Flex Battery Cable from XT60 to Anderson 45 (13+18 AWG)
  • 70 cm Phase (MT60), Halls (JST), prewired for the BBS-HD
  • 150 cm Phaserunner to Cycle Analyst V3 (new 8 pin waterproof CA plug, cableset with JST plug on request)
  • 1x Velcro Strechy Sleeve (Article 5503)

Temp-Sensor and PAS are used from the BBSHD, but can be used in a combination with a Cycle Analyst only. We also have a empty controller housing to hide the wiring.

3) Standard:

  • 80 cm High Flex Battery Cable from XT60 to Anderson 45 (2x 13 + 2x 18 AWG)
  • 115 cm Phase-/Hall-Cable from MT60 to Anderson 45 (12 AWG) and 2x JST for Hall
  • 1x Velcro Strechy Sleeve (Article 5503)

4) HiGo Z910

  • 80 cm High Flex Battery Cable from XT60 to Anderson 45 (13+18 AWG)
  • 97 cm Phase (MT60), Halls (JST) to 9pin waterproof Z910 HiGo motor plug
  • 9th pin wire lead is located under the heat shrink wrap on MT60 end of the harness. To be used for G31X speed pickup by replacing the 6th pin on the CA JST connector

Controller

  • Dimensions (L x W x H): 99 x 40 x 34 mm
  • Weight: 0.26 kg
  • Max Battery Amps: 50 A
  • Battery Range: 20V to 90V (21S Li-Ion, 24s LiFe)
  • Low Voltage Cutoff: Programmable
  • MOSFETs 6X 100V, 3mOhm
  • Made in Canada by Grin

Requires PC setup to mate and configure with a given motor, it will not be plug-and-play, and this requires the USB->TTL communications cable if you don't already have that.

It is ideally suited for running brushless motors for electric vehicles in the 500-2000 watt power range, and once you have experienced the smooth response of a FOC with a torque throttle it's hard to go back to a the setup you had before. This controller was designed as a universal device that can fit on almost any bicycle frame and handle almost any motor system. You can power it from a 24V battery or a 72V battery, and run your phase current to peaks of over 90 amps, though the continuous current capability without additional heatsinking is typically 45-50A. The wiring is paired down to the bare basics for a nice clutter-free installation. Including a throttle, Cycle Analyst and programming plug. Optional cable to your motor and cable to your battery pack.

Features

  • Remote on/off switch compatible
  • Direct plug for both V2 and V3 Cycle Analysts
  • Proportional regen available through throttle signal or stand alone wire
  • Works both Sensored and Sensorless, and even with very high eRPMs (60,000 eRPM+)
  • Waterproof, 100% potted electronics
  • Fully programmable parameters (regen voltage, max phase and battery currents etc.)
  • Field Weakening allows you to run motors faster than normal back-emf limit
  • Higher motor efficiency at low speeds / high torques
  • Torque based throttle command (no twitchy throttle with powerful system)
  • Automatic thermal rollback to prevent controller overheating

For much more information and software, go to the GRIN website, click here

and at Endless Sphere FORUM

For the BBSHD:

Unscrew the controller

cut out the hall sensor connector


connect Phase, Hall and PAS and seal the connectors with silicone
Also the temp sensor is used. You can order a empty controller housing in our webshop.


connect Battery, Phase, Hall, Cycle Analyst to the Phaserunner


to the Cycle Analyst: 5V to AUX, 10K thermistor, throttle, CA-connector from Phaserunner, PAS.

Use the Autotune software for the new setup, you need a programming cable

Some more infos and setup you can find on Endless Sphere

and also for the Ultra

Customer evaluation for "50A 30-90V Phaserunner Motor Controller V3"
Write an evaluation
Evaluations will be activated after verification.
Please enter these characters in the following text field.

The fields marked with * are required.

Programmierkabel für
Phaserunner
Cycle Analyst
Cycle Satiator
EMPFOHLEN
Anti-Blitz
bis 120A
EMPFOHLEN
Montagetool
für 2. Sicherungsring
Drehmoment
Ausbau Hollowtech 2
4 mm Disc spacer 6 holes
€6.99 * €9.99 *
rechts
ohne Stecker
EMPFOHLEN
Schaltsensor
für Ketten- und
Nabenschaltung
schont Kette
EMPFOHLEN
Montagetool
für 1. Sicherungsring
Drehmoment
40, 42, 44 Zähne
Spider als Adapter
verwendbar
z.B. Riemenscheibe
TIP!
5 Pin HIGO Cable
€4.99 * €7.99 *
Programmierkabel für
Phaserunner
Cycle Analyst
Cycle Satiator
TIP!
Topseller
sehr robust
bewährt
leise
TIP!
Maßakku
individuell
herstellbar
für 52V Akkus
2 Einstellungen
rechts
ohne Stecker
EMPFOHLEN
Schaltsensor
für Ketten- und
Nabenschaltung
schont Kette
42 Zähne
Versatz 23 mm
EMPFOHLEN
zusätzliche
Akkubefestigung
Viewed